Division Order Non-Operated Setups
How to setup the Header
Refer to the Division Order Header Level and Global Information page for details on setting up the Header and Relating the DO Assets
Non-operated DO Setups vary based on the type of interest owned by the Operator. Scenarios may include the following:
Working Interest
Overriding Royalty Interest (a burden interest)
Royalty Interest (a burden interest)
Combination of Working Interest and Burdens
Fundamentals of DI Calculation
Calculating the DI value correctly for a non-operated well can be complicated based on the interest owned by the operator and because there are a few different methods for ownership setup that can be used.
In its most simplest form, without the presence of a Balancing owner or Take-in-Kind owner and without the designation of being an Arkansas Operated Division Order, the DI value is calculated to equal the NRI value.
For the purpose of this document, the DI calculation will be described under the assumption that a balancing owner exists.
Balancing Interest Owner
Any interest type designated as a BI Interest Class in the Upstream Interest Types code table is considered a Balancing Interest [BI].
Anytime calculations are executed on a ownership cycle, the DI value will calculate as 0.000000000 for this interest type.
Burden Group Impact
When burden groups are not created, the system assumes, for calculation purposes, that they exist proportionately.
Thus, if an ownership cycle contains only a Balancing Interest and a burden such as a RI or ORRI, the system will assume that the Balancing Interest bears the entire RI/ORRI burden.
If the ownership cycle contains a WI and a BI together along with burdens and no burden group, the system will assume the WI and BI owner proportionately share in the RI/ORRI burdens.
In order to capture a scenario where the BI owner is simply a balancing owner and does not share in any burdens, a burden group indicating otherwise must be created and assigned to the burden owners.
Base vs Override Contract Impact and No Burden Groups
When a base contract is provided on an ownership cycle and there are no override contracts, the assumption by the system is that the single base contract is to be used for all owners in the queue and burdens should be allocated proportionately across any and all WI and BI owners.
If however a base contract is provided but then an override contract is assigned to the non-balancing interest directly in the owner queue, this difference in contracts breaks the assumption that burdens should be proportionately allocated and the owners are treated independently.
Non-Operated Setup Scenarios and Options
Working Interest Only
Ownership Queue contains a line for the Balancing Interest and a line for the Working Interest
Burden Groups are not needed because burdens do not exist
Override Contracts are not needed because burdens do not exist
When calculations are run, the Balancing Interest DI will equal 0.0000000 and the Working Interest DI will equal 1.000000000

Working Interest and Burdens combined
Ownership Queue contains a line for Balancing Interest, Working Interest, and the Burden Interest (i.e. RI/ORRI)
A burden group is needed because burdens exist
An override contract is not needed because burden groups exist
The burden group should contain the WI owner from the owner queue with an owner percent of 1.0
The burden group should be tied to the RI/ORRI line of interest in the owner queue
When calculations are run, the Balancing Interest DI will equal 0.00000000 and the DI for the WI and RI will be proportionately inflated based on the NRI values.

Burdens Only (option 1 - Burden Group)
Ownership Queue contains a line for Balancing Interest and a Burden Interest (i.e. RI/ORRI)
A burden group is needed because burdens exist
The burden group should contain a WI owner and NOT the BI owner
If the burden group contains the BI owner (instead of the WI owner) then the resulting DI of the burden interest (i.e. RI/ORRI) will be 0.00000
In order for the burden group to contain a WI owner, a WI owner line must be added to the Owner Queue
Because the WI owner does not technically own any interest, the NRI should be 0.00000
The burden group should be tied to the RI/ORRI line of interest in the owner queue
When calculations are run, the Balancing Interest DI will equal 0.00000000 and the DI for the WI and RI will be proportionately inflated based on the NRI values.

Burdens Only (option 2 - Override Contract)
Ownership Queue contains a line for Balancing Interest and a Burden Interest (i.e. RI/ORRI)
A burden group is not used
An override contract is needed because burden groups are not used
The Base Contract should be a placeholder
The true Contract should be tied to the Burden Interest (i.e. RI/ORRI) and added to the owner queue as an Override Contract
When calculations are run, the Balancing Interest DI will equal 0.00000000.
Because the only other interest in the owner queue is tied to a different contract from the base contract, the system assumes the Balancing Interest is NOT burdened by the burden interest.
Thus it disburses 1.0000 to the override contract, thus the burden interest receives a 1.0000 DI value
